Worker in navy work clothes guiding a thick black vacuum hose into an open ground-level access beside a tan block wall, a stainless tank truck parked behind him

Phoenix, AZ · Form open 24/7

Grease Trap Cleaning Phoenix, AZ

You run a kitchen in Phoenix and the grease trap or interceptor needs attention. Tell us the device, the kitchen and the last pump-out date. We will call you back shortly.

  • Form open 24/7
  • Phoenix + 15 Valley cities
  • Traps, interceptors, septic

Form open 24/7

Get a call back

Phoenix + 15 Valley cities

What you get

Commercial grease trap cleaning in Phoenix runs on two clocks. A hydromechanical trap under the sinks has to be pumped at least every 30 days and never left more than 90. A gravity interceptor buried outside has to be pumped and cleaned at least once every 3 months. Both rules come from Phoenix City Code 28-15, and both are floors, not targets: the device also has to be pumped whenever fats, oils and grease plus solids reach 25 percent of its capacity.

You can check your next due date, see what a pump-out should cost and see what an inspector will ask for. Tell us what your kitchen needs and someone from our team will call you back soon. Every price on this page is a range, labeled as national or Arizona.

What you get when you ask for a call back

  1. 01A call back. Someone phones you about the device and the kitchen you described.
  2. 02A due date. The Phoenix and Valley city rule that applies, with the next pump-out date.
  3. 03A price range. Sourced ranges by device size, before you agree to anything.
  4. 04The paperwork. A service record with the fields inspectors ask for, kept for 3 years.
Technician in a dark work shirt and a kitchen worker in an apron looking together at a tablet beside a three-compartment sink

01 / Schedule check

When is your next pump-out due?

Most overdue traps are not overdue because the owner ignored them. They are overdue because nobody wrote the date down. The service tag on the lid fades, the invoice goes into a shoebox, and the next thing anyone knows the kitchen smells like a fryer at 2 pm on a Friday.

Use the check below. Pick the city your kitchen drains into, the device type and the date on the last service record. It returns the rule that applies to that city, the next due date, the records you are expected to keep and the phone number for the city program that enforces it. No email gate, no signup.

Schedule check

Device
Open the full schedule check

Rules from the city codes, checked November 20, 2026.

Get a call back

Your result goes along with the call-back request.

If you do not know the device type, the next section explains the difference in plain terms. If you do not know the size, the service invoice usually lists it. If the invoice is gone, the grease trap lid often carries the manufacturer's rating in gallons or in gallons per minute.

03 / Price ranges

What a grease trap pump-out costs in Phoenix

There is no city-published price for a pump-out, because the work is private. The useful numbers are national price compilations and public bid results. The ranges below are national, not Phoenix-specific, and they move with device size, access, volume and how often the device is serviced.

DeviceTypical capacityScheduled priceOne-off or overdue price
01Indoor hydromechanical trap20 to 100 gallons$125 to $325 per visit$150 to $400
02Small outdoor interceptor500 to 1,000 gallons$225 to $400 per visit$300 to $500
03Mid-size interceptor1,000 to 1,500 gallons$225 to $315 on a service plan$320 to $630
04Large interceptor2,000 to 2,500 gallons$400 to $700 per visit$630 to $1,000
05Very large or multi-tank3,000 gallons and up$800 to $2,000 per visit$1,000 to $2,000 or more

Per gallon

The per-gallon side is worth knowing because it makes two quotes comparable. Public contract bids for hauling and disposal have landed between $0.14 and $1.95 per gallon, with most bids between $0.20 and $0.85. A hauler quoting $0.50 per gallon on a 1,000 gallon tank is quoting about $500, which is high for a scheduled service and reasonable for an emergency at 9 pm.

Worked example

A worked example. A full-service restaurant in central Phoenix with a 1,000 gallon outdoor interceptor on a 90 day schedule is looking at 4 pump-outs a year. At $225 to $400 per scheduled visit, that is $900 to $1,600 a year, plus whatever the device needs in repairs. A smaller cafe with a 50 gallon under-sink trap on a 30 day schedule is looking at 12 visits. At $125 to $200 per visit, that is $1,500 to $2,400 a year, which is the part most owners miss when they choose a small trap to save money on the install.

What moves the price:

  • 01Device size and how full it is. A device at 60 percent costs more than the same device at 20 percent.
  • 02Access. A lid under a parked car, behind a locked gate or under a grease-soaked mat adds labor.
  • 03Distance to the disposal site and the disposal fee the hauler pays.
  • 04Time of day. Nights, weekends and service-hour emergencies carry a premium.
  • 05Frequency. Scheduled service is cheaper per visit than one-off pumping in the price guides reviewed.
  • 06Condition. A broken baffle, a collapsed lid or a tank full of hardened solids turns a pump-out into a repair.

A quote that lists the device size in gallons, the volume removed, the disposal fee, the manifest, whether the walls and baffles are included and the disposal site can be compared line by line with another. A single number with no gallons on it cannot. The cost page goes deeper on ranges by device type and on how to read two quotes side by side.

Price check

Get a price range for your kitchen

Tell us the device, the city and the date of the last pump-out. Someone calls you back about that kitchen.

  • 01The city the kitchen drains into
  • 02Indoor trap or outdoor interceptor
  • 03The date of the last pump-out

Thank you. You will be called back soon.

04 / Code 28-15

The Phoenix rule, in one table

Phoenix City Code 28-15 is short and specific. The table below is the operating summary. The code itself, Phoenix City Code 28-15 (opens in a new tab), is the authority.

CODE 28-15Phoenix City Code 28-15Read the code (opens in a new tab)
  • 28-15 D01Hydromechanical interceptorFully pumped and cleaned at least every 30 days unless the Director grants a variance, and never more than 90 days without maintenance
  • 28-15 C02Gravity interceptor at a food service establishmentFully pumped and cleaned at least once every 3 months, unless the Director grants a variance
  • 28-15 B03Gravity interceptor, other usersAt least once every 12 months
  • 28-15 B04Capacity limitFOG, lint, oil, sand, sludge and solids must not exceed 25 percent of total liquid volume
  • 28-15 F05RecordsCleaning, volume removed, device capacity, disposal, repair and maintenance records kept at the facility for 3 years
  • 28-15 G06Chemicals and enzymesChemicals, enzymes, proteins, bacteria, solvents and emulsifiers used in place of physical cleaning are prohibited

Two parts of that table catch owners out. First, the 30 day rule for a hydromechanical device is not a suggestion that a quarterly visit satisfies. Second, Phoenix prohibits chemicals, enzymes, proteins, bacteria, grease solvents and emulsifiers used to temporarily dissolve grease, so an enzyme product that claims to eliminate pumping is not a maintenance plan under this code.

Tempe, Scottsdale, Mesa, Chandler, Gilbert, Glendale, Peoria and the Salt River Pima-Maricopa Indian Community each publish their own version. Some match Phoenix, some are looser, and Mesa publishes no interval at all. The pumping schedule page carries the full table with a source link for each city, and the schedule check applies it to your date.

05 / Trap or interceptor

Trap or interceptor: which one does your kitchen have?

The easiest test is location. If the device is a metal box under the three-compartment sink or in a closet beside it, it is a hydromechanical trap, and it is rated in gallons per minute and pounds of grease, not in hundreds of gallons. If it is a concrete or fiberglass tank under the parking lot with round lids at grade, it is a gravity interceptor, and it is rated in gallons.

The second test is the fixture count. Tempe's program puts it simply: 4 or fewer kitchen fixtures on the grease line can use a trap, and more than 4, or any commercial dishwasher, needs an interceptor. Phoenix's FOG manual draws a similar line: a gravity interceptor is required for more than 4 plumbing fixtures, and for any food service establishment with a dishwasher or a food waste disposal unit.

Where it sitsHydromechanical trapUnder or beside the sink, indoors, metal bodyGravity interceptorBuried outside, concrete or fiberglass, lids at grade
Typical sizeHydromechanical trap20 to 100 gallons, or rated in gallons per minuteGravity interceptor500 to 2,500 gallons, some larger by engineering design
Phoenix intervalHydromechanical trapEvery 30 days, never more than 90Gravity interceptorAt least every 3 months for a food service establishment
Who empties itHydromechanical trapA pumper with a vacuum hose and hand toolsGravity interceptorA vacuum truck, usually 2,500 gallon capacity
What a visit includesHydromechanical trapPump, scrape the baffles, clean the lid gasketGravity interceptorFull pump-out, wall scraping, baffle and lid check, manifest
Common failureHydromechanical trapBaffle missing, gasket gone, trap undersized for the menuGravity interceptorSolids not agitated, outlet blocked, lid cracked
1234567
  1. 01Inlet Kitchen wastewater enters through the inlet tee on the left.
  2. 02Baffle The wall between the compartments holds back the floating layer and lets clearer water pass underneath.
  3. 03FOG layer Fats, oils and grease float to the top and form the mat.
  4. 04Water The clarified middle layer is the liquid volume the 25 percent limit is measured against.
  5. 05Solids Food solids and sludge settle on the bottom.
  6. 06Outlet tee The outlet draws from below the mat, so only water leaves for the sewer.
  7. 0725 percent line Grease and solids together must stay under a quarter of the liquid volume.

Size matters for scheduling in a way that is easy to miss. A 50 gallon trap in a busy kitchen can hit 25 percent in 3 weeks. A 1,500 gallon interceptor in a low-volume cafe can still be under 25 percent at 90 days, but the city calendar still applies. Whichever limit arrives first is the one that matters.

06 / 7 steps

How a pump-out actually runs

Knowing the sequence is useful for two reasons: you can tell whether the trap was fully cleaned or only the liquid was pulled, and you can plan the 45 to 90 minutes a pump-out takes out of a service day.

  1. Arrive and set up

    The truck parks close to the lids, hoses run, and the work area is covered before anything opens.
  2. Open and read the device

    Lids come off, the FOG mat and solids are measured, and the inlet and outlet are checked for a blockage.
  3. Pump the liquid

    The vacuum pulls the liquid and the floating grease out first, so the walls can be reached.
  4. Scrape the walls and baffles

    Grease sticks to the sides and the underside of the baffles. Pumping alone leaves a film that hardens.
  5. Clean and inspect

    The compartment is hosed, the baffles, lids and gaskets are checked, and a cracked lid or missing outlet is noted.
  6. Close and log

    Lids are reset, the volume removed is written on the manifest and the service log gets a copy.
  7. Haul and dispose

    Waste goes to a permitted disposal site, and that site is named on the manifest.

Three details separate a full pump-out from a partial one. The hose reaches the lid without driving over a grease mat or a drain. The FOG mat and the solids are measured before pumping, because the numbers on the manifest are the only record of how fast the device fills. And the lids go back on seated, with the gasket in place, because a lid that sits proud lets in runoff and a missing gasket lets odor out.

07 / Inspector file

What to keep for the inspector

Every Valley program asks for records, and the differences are in the details. Phoenix requires 3 years at the facility and lists the specific items. Chandler lists 5 items and 3 years (Chandler's page says records should be retained on site for 3 years). Tempe asks for pump-out records on site. Mesa asks for written cleaning, repair, calibration and maintenance records for 3 years. Gilbert points to 66-243(d). Scottsdale, Glendale, Peoria and Surprise all land on 3 years.

A service log that satisfies all of them contains:

Two habits make the file survive an inspection. Keep the paper in the kitchen, not in a manager's car, because these programs say the records stay on site or at the facility. And photograph the service tag on the lid each time, because a phone photo with a date is the cheapest backup record there is.

  • 01The date of every service, including the ones that were just an inspection.
  • 02The name and address of the hauler, and the permit or license number if the city asks for it.
  • 03The device type, the rated capacity in gallons or GPM, and the location on the property.
  • 04The volume removed at each service, in gallons.
  • 05The disposal site, with the date and the quantity received.
  • 06Any repair, baffle replacement, lid replacement or calibration.
  • 07The signature or initials of the person who watched the service, where the city requires a witness.

08 / Warning order

Signs the device is past due

A grease trap does not fail loudly. It gives warnings for a week or two before it turns into a floor drain full of grey water at 7 pm on a Saturday.

01 / Early

  • 01

    Slow sink drains

    Water stands in the sink longer than it did last month. The trap is holding solids, not just grease.

02 / Middle

  • 02

    Smell in the kitchen

    A grease trap that is past due vents odor back into the room, usually near the mop sink or the floor drain.

  • 03

    Grease in the outlet

    The outlet compartment shows a grease layer. That means grease is getting past the device and into the sewer line.

03 / Late

  • 04

    Floor drain backup

    Grease in the line between the trap and the sewer. A pump-out alone does not clear a blocked line.

  • 05

    Broken baffle or lid

    A missing baffle sends grease straight through. A cracked lid lets in runoff and debris.

The order matters. A slow drain is early. A smell is middle. A floor drain backup is late, and by then the problem is usually in the line, not just the tank. If the floor drain is already backing up, emergency help for a grease backup comes first and the price comes second.

09 / The 25 percent rule

What the 25 percent rule looks like in the device

The 25 percent rule is the part of the code that nobody argues about until an inspector measures. It does not care about the calendar. It says the combined grease, oil, sand, sludge and solids in the device may not exceed 25 percent of the total liquid volume. In a 1,000 gallon interceptor, that is 250 gallons of stuff before the device is out of compliance. In a 50 gallon trap, it is 12.5 gallons, which arrives fast in a kitchen that serves 200 covers a day.

The measurement is simple and it is done with a tool called a sludge judge, or with a weighted tape and a steady hand. The pumper lowers the tool until it touches the grease mat, reads the depth, then pushes through the mat and the liquid until it touches the solids, and reads again. The two depths, multiplied by the surface area of the compartment, give the volume. Divide by the tank capacity and the percentage is the number the city cares about.

DeviceCapacity25 percent limit
Under-sink trap50 gallons12.5 gallons
Commercial trap100 gallons25 gallons
Small interceptor500 gallons125 gallons
Mid interceptor1,000 gallons250 gallons
Large interceptor2,000 gallons500 gallons

The depth that equals 25 percent depends on the shape of the compartment, so the depths are read at each pump-out and the percentage is worked out for that device. A 50 gallon trap reaches the limit at 12.5 gallons of mat and solids, and a 1,000 gallon interceptor at 250 gallons, which is why a 30 day trap schedule and a 90 day interceptor schedule can both be right for the same kitchen.

The practical advice is to record the depths at every pump-out. Depths written down give you a trend line. A calendar alone does not. The trend line is what lets a restaurant justify a variance, plan a replacement or catch a device that is filling faster than it used to.

10 / City rules

How the Valley rule books differ

Phoenix is the default here, but the metro is a patchwork. The same kitchen with the same menu can be on a 30 day clock in Phoenix, a 180 day clock in Glendale and no calendar at all in Mesa, depending on which city sewer the address drains to.

CityTrapInterceptorWhat it means for a restaurant
Phoenix30 days, max 9090 daysThe same 30 day trap clock as Tempe and Scottsdale
Tempe30 days90 daysSame shape as Phoenix, different code section
Scottsdale30 days90 daysSame shape, with 3 year records
MesaNo fixed intervalNo fixed intervalContinuous operation is the standard
ChandlerNo fixed intervalNo fixed intervalThe 25 percent rule of thumb sets the timing
Gilbert6 months6 monthsOne of the longest published intervals
Glendale180 days180 days3 year records still apply
Peoria90 days90 daysMatches the Phoenix interceptor interval
SurpriseNo fixed intervalNo fixed interval3 year records apply

The restaurant does not get to choose: the address decides.

Two practical consequences follow. A multi-unit operator has to build the schedule per location, not per brand. And a restaurant that moves or opens a second location has to re-check the rule, because the new address may be in a different system with a different clock.

11 / Who does the work

Who shows up, and what the truck should carry

A grease pump-out is a small industrial operation. The truck is a vacuum tanker, usually 2,500 gallons, with a pump, a hose reel and a set of hand tools. A pump-out is often a 1 or 2 person job. The visit is scheduled, and access is confirmed ahead of it.

The truck carries a sludge judge or a measuring tape, a scraper, a hose long enough to reach the lids without driving over a drain, absorbent for spills, and a manifest book that names the disposal site. In Maricopa County, the vehicle needs a non-hazardous liquid waste permit from Environmental Services, and each approved vehicle carries the number the county assigns.

A visit that pumps only the liquid, leaves the walls coated, skips the measurement or lists no gallons on the invoice is a partial visit, and the device refills early.

If the restaurant has a grease interceptor in a drive lane, the visit needs a plan for the cars. If the lids are under a patio, the visit needs a plan for access. If the kitchen is on the second floor of a mixed-use building, the truck needs to know before it arrives, because a 100 foot hose run changes the job.

Rust-edged concrete interceptor chamber seen from above with a white tee fitting on the far wall and shallow water in the bottom

12 / New kitchens

Opening a restaurant in Phoenix

A new restaurant usually meets the grease rule twice: once at plan check, when the device is sized, and once at the first inspection, when the device is checked. The sizing depends on the fixture count, the menu and the plumbing code the city has adopted. Phoenix checks gravity interceptors through its plans process, and Tempe's program is explicit that more than 4 kitchen fixtures, or any commercial dishwasher, needs an interceptor rather than a trap.

The order of work is: plumbing plan, device sizing, permit, installation, inspection, then a service schedule. Skipping the sizing step is expensive, because an undersized device can fail the 25 percent rule on the city's calendar, and the fix can be a new tank.

Three things to decide before the first service: who watches the pump-out, where the manifests are kept, and who is responsible for the device in the lease. A restaurant that answers those 3 questions at opening avoids a common first-year compliance problem, which is a device that was pumped but cannot be proven.

13 / Manifest

What a service record looks like

A record that survives an inspection is short, specific and boring. Here is a single row from a service log, filled in the way the Valley programs expect.

Ten fields, one line, 2 minutes. Multiply by 4 visits a year and the file builds itself. Multiply by 12 for a trap on a 30 day schedule and the file is still only 12 rows.

The row does 3 jobs. It proves the visit happened. It shows whether the device is filling faster or slower than last time. And it gives the next pumper a starting point, which is how a schedule gets tuned instead of guessed.

The comparison across rows is where the value compounds. If the grease depth is 6 inches in January, 8 in April and 10 in July, the device is filling faster and the interval should shrink before the calendar catches up. If the depths are flat at 5 inches for a year, the device is well sized and the interval is generous, which is the evidence a variance request needs.

A restaurant that keeps this log for 3 years has something more useful than a compliance file. It has a maintenance history that makes the device predictable, and predictable devices are the ones that do not back up on a Saturday.

SERVICE LOGROW 01 / 10 FIELDS

01Date
2026-10-14
02Device
Gravity interceptor, 1,000 gallons, north lot
03Hauler
Company name and address
04Volume removed
940 gallons
05Grease depth before pump
9 inches
06Solids depth before pump
7 inches
07Disposal site
Permitted facility, city and state
08Repairs noted
Outlet baffle loose, tightened
09Watched by
Manager initials
10Manifest filed
Current year tab, page 14

MANIFEST FILED / KEEP 3 YEARS

14 / Costs

The mistakes that cost the most

  • Pumping only the liquid. The grease on the walls stays, the device refills early and the schedule fails.
  • Skipping the measurement. Without depths, nobody knows whether the 25 percent limit arrives before the calendar.
  • Using an additive as a substitute. Phoenix prohibits it, and it hides the problem instead of removing it.
  • Losing the manifest. The pump-out happened, but the record does not exist, which is a violation on its own.
  • Ignoring a slow drain. A slow drain is the cheapest warning in the system and the last one before a backup.
  • Choosing the smallest legal device. A small trap is cheaper at installation and more expensive every month after.
Gloved hand scrubbing the dark baffle plate of an open trap with a yellow brush, terracotta tile floor beside it

15 / Why us

Why choose Grease Trap Cleaning Phoenix?

Facts to read before you send the form.

  • 01

    Licensed for repairs.

    Phoenix grease trap repair and replacement is done under an active Arizona ROC license.

    How to check a license
  • 02

    Permitted pumpers.

    Every Phoenix pump-out is done by a hauler with a Maricopa County liquid waste permit.

    The 3 license steps
  • 03

    Start your quote.

    We will call you back shortly.

  • 04

    Phoenix + 15 Valley cities.

    One page for each city, with the rule that applies there.

    See the areas
  • 05

    Every rule linked to its city code.

    Each figure on the rule tables points to the page that states it.

    The Phoenix rules

Contractor license

How to Check an Arizona Contractor License

A license lookup is a public record search. It takes a few minutes and it is worth doing before a repair, a replacement or any plumbing work on a grease device. How to check a license.

Technician kneeling at an open drain access holding a jetting hose, a red pressure washer unit on wheels behind him

16 / Service area

Where the work happens in Phoenix

Phoenix is not one restaurant market. It is a grid of districts with different building ages, different menus and different plumbing. A kitchen in a 1960s building on Grand Avenue and a kitchen in a 2019 build in Desert Ridge can have the same menu and completely different grease problems. The older building often has a trap sized for a coffee shop, the newer one has an interceptor sized by an engineer, and the two need different calendars even though both are in Phoenix.

Eight Phoenix districts first, then the Valley cities around them.

17 / Guides

Guides for the questions that come up every week

The guides are written for the person who runs the kitchen, not for a plumbing exam. Each one answers a question that comes up in the first 5 minutes of a service call.

Quick answers to what kitchen managers ask before a quote. Pick the topic that fits.

18 / 10 questions

Questions Phoenix restaurant owners ask

Still have a question?

Send the form with a short note. Someone from our team will call you back soon.

Get a call back

Q.01

How often does a grease trap need to be pumped in Phoenix?

A hydromechanical trap at least every 30 days and never more than 90 days. A gravity interceptor at a food service establishment at least every 3 months. Both are floors: the device also has to be pumped before FOG and solids reach 25 percent of its capacity, so a busy kitchen may need service more often than the calendar requires.

Q.02

Who can pump a grease trap in Phoenix?

The work is done by a liquid waste hauler. In Maricopa County, a vehicle that removes, transports or disposes of non-hazardous liquid waste needs an operating permit from Maricopa County Environmental Services, and the permit is tied to the vehicle.

Q.03

How much does grease trap cleaning cost in Phoenix?

National ranges run $125 to $325 for a small indoor trap, $225 to $400 for a 1,000 gallon interceptor on a schedule, and $400 to $700 for a 2,000 gallon tank on a schedule. Per-gallon bids on public contracts have landed between $0.14 and $1.95. Phoenix does not publish a price for private pumping, and the cost page lists what moves the number.

Q.04

What happens if I fail a FOG inspection?

It depends on the city, but the usual sequence is a notice with a correction deadline, a re-inspection, and a requirement to pump immediately and provide the manifest. Phoenix can require extra pumping or a device repair. Chandler requires the cleaning frequency to increase if grease is seen leaving the device. The failed inspection page walks through the process without giving legal advice.

Q.05

Do enzymes or bacteria replace pumping?

No. Phoenix City Code 28-15 G prohibits chemicals, enzymes, proteins, bacteria, grease solvents and emulsifiers used in place of physical cleaning. Chandler's code 51-24 prohibits additives that cut pumping. A product can be part of a maintenance routine; it cannot be the routine.

Q.06

How long does a grease trap pump-out take?

A 50 to 100 gallon indoor trap is usually 30 to 45 minutes including setup. A 1,000 to 1,500 gallon interceptor is usually 45 to 90 minutes, depending on access and how full it is. A tank over 2,500 gallons may need more than one truck load, which can push the visit past 2 hours.

Q.07

Can a restaurant clean its own grease trap?

A small indoor trap can be cleaned by staff in some jurisdictions, but the waste still has to be disposed of lawfully, and the record still has to satisfy the city. Chandler's page notes that most people do not attempt it more than once, and that even a small device holds at least 25 gallons of liquid waste that cannot go into the trash. For an outdoor interceptor, the equipment and the disposal permit make self-cleaning impractical.

Q.08

Does a food truck need a grease trap?

A food truck that washes utensils needs a commissary, and commissaries are required to have a grease removal device. Mesa's commissary requirements state that a commissary must have a grease interceptor or trap. The truck itself may have a small trap, but the wash water has to go to a permitted device, not to the ground or a storm drain.

Q.09

What records does an inspector ask for?

The date of service, the hauler's identity, the device capacity, the volume removed, the disposal site and any repairs. Phoenix requires 3 years at the facility. Chandler lists 5 required items and 3 years. Tempe and Mesa require records on site. Keep the manifests, the invoices and the service log together, and keep a photo of each service tag.

Q.10

Is a grease interceptor the same as a septic tank?

No. An interceptor separates grease and solids from kitchen wastewater before it enters the sanitary sewer. A septic tank treats all the wastewater from a building that is not connected to a sewer. Septic systems serve buildings beyond the sewer, such as some properties in Cave Creek and Paradise Valley, and Maricopa County regulates them. The grease device sits ahead of the tank, and commercial septic tank pumping covers the tank itself.

Send a messageSomeone calls you back
White vacuum service truck with a polished cylindrical stainless tank and coiled hoses parked behind a restaurant at sunset

Form open 24/7

Ask for a call back about your grease trap

Tell us which device and which kitchen. We will call you back shortly.

Thank you. You will be called back soon.

Grease backing up?Get a call back

Before you go: want a call back?

Give your name, phone number, ZIP code and the service you need. Someone will call you back about your grease trap.

Thank you. You will be called back soon.

Get a call back

Send it, and someone calls you back soon

Add details (optional)
How urgent is it?

The form is open day and night, and we will call you back shortly.

Get a call back

Send the form and someone calls you back soon.

Thank you. You will be called back soon.